If you are looking for the best, this is a high quality power supply for your MiSTer FPGA setup, you need look no further as this is possibly the ultimate MiSTer power supply providing clean power at 5 volts and up to 4 amps, plenty of overhead for any additional power requirements.
Mean Well are a respected industrial power supply manufacturer, these highly reliable desktop styled solutions come equipped with either a 2 pole IEC320-C8 AC inlet or a 3 pole IEC320-C14 AC inlet, allowing for an input range of 85 volts AC to 264 volts AC making it suitable for most countries. This power supply boasts an efficiency rating of over 81%, coupled with an extremely low no-load consumption rating of below 0.075 W. The power supply is equipped with industry standard protection, such as short circuit, overload and over voltage.
✅ Rated Output Power 20W
✅ Input Voltage Range 85 to 264 V AC
✅ Efficiency Over 81%
✅ Power Status LED Indication
✅ 3 Year Warranty
MiSTer Power Supply Compatibility:
✅ Terasic DE10-Nano
✅ Retro Remake MiSTer Pi (USB C Adapter Required)
✅ QMTECH Cyclone V
| Power Socket Type: | 2 Pin IEC320 C8, 3 Pin IEC320 C14 |
|---|
Be the first to review “MiSTer FPGA Power Supply 5 Volt 4 Amps”
Related products
When using a SNAC adapter with the MiSTer to avoid any strain on the User IO port, the recommended connection setup is to use a short male to female USB 3.0 extension cable between the SNAC adapter and the User Port on the MiSTer IO board. This high quality USB 3.0 extension has a shielded [...]
Accessories
This neat little plug designed and produced by MiSTer Addons allows you to connect the Digital IO board and DE10-Nano DC power sockets together. The DC jumper is only used with the Digital IO board or BlisSTer board. To use the built in Digital IO board power switch, simply link your power supply to the [...]
Accessories
When connecting the Raspberry Pi based MT32-Pi to the MiSTer via a USB 3.0 A-to-A cable, it’s important to use a short cable to ensure stable performance, this MT32-Pi USB 3.0 cable is the perfect choice. Since I²C is not intended for long-distance transmission, longer cables can cause degradation due to capacitance or signal reflections. [...]
Accessories
The power supply splitter cable is connected to the male end of the power supply or the male end of an inline power switch, with two male connectors at each end of the splitter plugging directly into the DE-10 Nano board and USB hub board. ✅ For Original & Aftermarket Power Supplies ✅ High Quality [...]
Accessories
A male DC jack to male DC jack jumper cable, this is perfect for use with a MiSTer Digital IO board allowing for powering of the USB Hub directly from the DE10-Nano. If you are using the Digital I/O MiSTer addon board just connect your DE10-Nano power supply into the Digital IO boards DC power [...]
Accessories
A two meter long mains cable with IEC C7 (figure of 8) connector and a selection of interchangeable country specific plug heads, this is designed to allow electricity to flow from point A to point B 🙂 Perfect for use with this high quality MiSTer DE10-Nano power supply. ✅ 2 Meter Long Cable ✅ UK [...]
Accessories
If you are using the high-quality MiSTer Mean Well power supply or any other power supply with a DC barrel plug, this adapter cable allows you to connect it to the MiSTer Pi’s USB-C power input socket. Simply plug the USB-C end into the MiSTer Pi’s power input, and then connect the female DC socket [...]
Accessories
If you have a MiSTer USB Hub with a wired Micro USB cable attached, and wish to streamline your MiSTer setup this connector kit offers a neat low profile connection via a right angled gold plated Micro USB connector which plugs into the DE10 Nano boards Micro USB socket, the 4 pin socket plugs directly [...]
Reviews
There are no reviews yet.